ppalias

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 1,137 total)
  • Author
    Posts
  • in reply to: equipment conectivity using tera term #52549
    ppalias
    Member

    The pc that you are trying to connect to the cisco switch has which IP,mask and gw? So far I don’t see anything wrong. Maybe you could post the firewall rules too.

    in reply to: equipment conectivity using tera term #52547
    ppalias
    Member

    What are the IPs, masks and gateways of each device?

    in reply to: USB 3G Modem Not Working with Zeroshell #51294
    ppalias
    Member

    You can always compile it and use the newer version, rather than the one found in ZS. There are instructions about building modules in ZS, follow them to get the compiling tools.

    in reply to: Need help with Bridge installation #51322
    ppalias
    Member

    Then you had better not run DHCP server on ZS directly connected on the university network.
    Are you sure the old bridge is just bridging the two network interfaces, rather than doing something else? The whole setup is pretty straight and the fact that it is not working makes me wonder if you are missing something. If you omit both the old bridge and the ZS and connect the laptop directly on the university network, does it work?

    in reply to: USB 3G Modem Not Working with Zeroshell #51292
    ppalias
    Member

    I am not sure for that.

    -v 12d1 -p 140b

    looks correct but maybe you need to pass some more arguments or create a config file. You need to search it a little bit more on the internet and practice with your usb.

    in reply to: USB 3G Modem Not Working with Zeroshell #51290
    ppalias
    Member

    It still is recognized as storage device rather than a modem. Try again with the usb_modeswitch.

    in reply to: Need help with Bridge installation #51320
    ppalias
    Member

    That proves what I am saying about security. I suppose that the university requires you to acquire IP address via dhcp. Are you acquiring IP from their DHCP on your ZS? Maybe if you don’t get IP from their dhcp no traffic is allowed to your ZS.

    in reply to: USB 3G Modem Not Working with Zeroshell #51287
    ppalias
    Member

    When you plug in the usb, what is the output of

     dmesg | tail -n 100
    in reply to: QoS Captive Portal #51303
    ppalias
    Member

    @diviesh wrote:

    I had a look at that but was a little concerned about changing to bridge mode will the captive portal still work??

    Nevermind about bridge mode. Stick to the QoS tutorial.

    in reply to: Need help with Bridge installation #51318
    ppalias
    Member

    It also looks like you are not learning anything in the ARP table from the ETH00 interface. Maybe your university is blocking the MAC address of the ZS, or they are applying some kind of security, such as 802.1x .
    Apart from that your configuration looks fine to me. You can try it by connecting two workstations on the two interfaces (in the same subnet) and see if they can ping each other.

    in reply to: VMWare/Zeroshell and HP VLANs #51311
    ppalias
    Member

    The

    ifconfig -a

    can show you the available interfaces, so if you see any of them marked like

    ethXX.YY

    it most likely is a vlan subinterface.

    in reply to: USB 3G Modem Not Working with Zeroshell #51284
    ppalias
    Member

    Have you unplugged-plugged in the usb?
    What is the output of the following?

    ls -l /dev/ttyUSB*
    ifconfig -a

    Run these commands with usb plugged in.

    in reply to: QoS Captive Portal #51300
    ppalias
    Member

    First of all read the documentation and if you still have questions you can ask them here.

    in reply to: Need help with Bridge installation #51316
    ppalias
    Member

    You have assigned 2 IP addresses in the BRIDGE00 that are in the same subnet. Either remove one or change one to be in another subnet.

    in reply to: VMWare/Zeroshell and HP VLANs #51309
    ppalias
    Member

    As far as I know this is red hat linux based, correct? Try to add the vlan on the interface with the command

    vconfig
    Usage: add [interface-name] [vlan_id]
    rem [vlan-name]
    set_flag [interface-name] [flag-num] [0 | 1]
    set_egress_map [vlan-name] [skb_priority] [vlan_qos]
    set_ingress_map [vlan-name] [skb_priority] [vlan_qos]
    set_name_type [name-type]

    * The [interface-name] is the name of the ethernet card that hosts
    the VLAN you are talking about.
    * The vlan_id is the identifier (0-4095) of the VLAN you are operating on.
    * skb_priority is the priority in the socket buffer (sk_buff).
    * vlan_qos is the 3 bit priority in the VLAN header
    * name-type: VLAN_PLUS_VID (vlan0005), VLAN_PLUS_VID_NO_PAD (vlan5),
    DEV_PLUS_VID (eth0.0005), DEV_PLUS_VID_NO_PAD (eth0.5)
    * bind-type: PER_DEVICE # Allows vlan 5 on eth0 and eth1 to be unique.
    PER_KERNEL # Forces vlan 5 to be unique across all devices.
    * FLAGS: 1 REORDER_HDR When this is set, the VLAN device will move the
    ethernet header around to make it look exactly like a real
    ethernet device. This may help programs such as DHCPd which
    read the raw ethernet packet and make assumptions about the
    location of bytes. If you don't need it, don't turn it on, because
    there will be at least a small performance degradation. Default
    is OFF.
Viewing 15 posts - 1 through 15 (of 1,137 total)