xtacy

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 16 total)
  • Author
    Posts
  • in reply to: ISP connection setup problem #51171

    xtacy
    Member

    thanx, that made both connections Active at NB. And the Utils’s Ping works fine but it did b4 anyway, what’s the point?
    And what if second ISP’s GW would change? Should i monitor this situation all the time?

    And the next looks like a huge bug! I did the following via web interface:
    1) In the Network setup – unchecked ETH01 “Up” chkbox
    2) In the Network setup – unchecked PPP0 “Up” chkbox
    3) Reboot ZS
    After reboot in the in the Network setup ETH01 “Up” chkbox stays unchecked while PPP0 is checked on and IT IS CONNECTED!!! How’s that could happen? It looks 4me like 1st ISP’s PPPoE goes via 2nd ISP. I believe both ISPs wouldn’t thank me for that if it’s so!

    in reply to: ISP connection setup problem #51169

    xtacy
    Member

    that’s what i got with the only ETH02/ISP2 connected (unchecked ETH01/ppp0’s Up and reboot ZS):

    root@zeroshell root> ifconfig
    ETH00 Link encap:Ethernet HWaddr 00:E0:F4:15:A4:64
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:2460 errors:0 dropped:0 overruns:0 frame:0
    TX packets:1573 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:215186 (210.1 Kb) TX bytes:370142 (361.4 Kb)
    Interrupt:24 Base address:0xc000

    ETH00:00 Link encap:Ethernet HWaddr 00:E0:F4:15:A4:64
    inet addr:10.54.29.1 Bcast:10.54.29.255 Mask:255.255.255.0
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    Interrupt:24 Base address:0xc000

    ETH01 Link encap:Ethernet HWaddr 00:E0:F4:15:A4:65
    inet addr:10.33.169.85 Bcast:10.33.169.127 Mask:255.255.255.128
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:485 errors:0 dropped:0 overruns:0 frame:0
    TX packets:673 errors:0 dropped:0 overruns:0 carrier:0
    collisions:20 txqueuelen:1000
    RX bytes:96800 (94.5 Kb) TX bytes:76935 (75.1 Kb)
    Interrupt:25 Base address:0xc400

    ETH02 Link encap:Ethernet HWaddr 00:E0:F4:15:A4:66
    inet addr:188.230.21.97 Bcast:188.230.21.255 Mask:255.255.254.0
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:4002 errors:0 dropped:0 overruns:0 frame:0
    TX packets:1925 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:276933 (270.4 Kb) TX bytes:115782 (113.0 Kb)
    Interrupt:26 Base address:0xc800

    dummy1 Link encap:Ethernet HWaddr DA:65:93:83:13:E7
    inet addr:192.168.142.142 Bcast:192.168.142.255 Mask:255.255.255.255
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:337 errors:0 dropped:0 overruns:0 frame:0
    TX packets:337 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:34827 (34.0 Kb) TX bytes:34827 (34.0 Kb)

    root@zeroshell root> iptables -L -v
    Chain INPUT (policy ACCEPT 623 packets, 64569 bytes)
    pkts bytes target prot opt in out source destination
    1263 176K SYS_INPUT all — any any anywhere anywhere
    0 0 SYS_HTTPS tcp — any any anywhere anywhere tcp dpt:http
    214 36243 SYS_HTTPS tcp — any any anywhere anywhere tcp dpt:https
    125 9652 SYS_SSH tcp — any any anywhere anywhere tcp dpt:ssh

    Chain FORWARD (policy ACCEPT 2531 packets, 172K bytes)
    pkts bytes target prot opt in out source destination

    Chain OUTPUT (policy ACCEPT 581 packets, 263K bytes)
    pkts bytes target prot opt in out source destination
    1750 356K SYS_OUTPUT all — any any anywhere anywhere

    Chain NetBalancer (0 references)
    pkts bytes target prot opt in out source destination

    Chain SYS_HTTPS (2 references)
    pkts bytes target prot opt in out source destination
    0 0 ACCEPT all — lo any anywhere anywhere
    214 36243 ACCEPT all — any any anywhere anywhere

    Chain SYS_INPUT (1 references)
    pkts bytes target prot opt in out source destination
    219 21117 ACCEPT all — lo any anywhere anywhere
    62 26116 ACCEPT udp — any any anywhere anywhere udp spt:domain state ESTABLISHED
    17 18552 ACCEPT tcp — any any anywhere anywhere tcp spt:http state ESTABLISHED
    0 0 ACCEPT tcp — any any anywhere anywhere tcp spt:8245 state ESTABLISHED
    3 228 ACCEPT udp — any any anywhere anywhere udp spt:ntp state ESTABLISHED
    962 110K RETURN all — any any anywhere anywhere

    Chain SYS_OUTPUT (1 references)
    pkts bytes target prot opt in out source destination
    1003 82254 ACCEPT all — any lo anywhere anywhere
    133 9144 ACCEPT udp — any any anywhere anywhere udp dpt:domain
    21 1172 ACCEPT tcp — any any anywhere anywhere tcp dpt:http
    0 0 ACCEPT tcp — any any anywhere anywhere tcp dpt:8245
    12 912 ACCEPT udp — any any anywhere anywhere udp dpt:ntp
    581 263K RETURN all — any any anywhere anywhere

    Chain SYS_SSH (1 references)
    pkts bytes target prot opt in out source destination
    0 0 ACCEPT all — lo any anywhere anywhere
    125 9652 ACCEPT all — ETH00 any 10.54.29.3 anywhere
    0 0 DROP all — any any anywhere anywhere
    root@zeroshell root> iptables -t nat -L -v
    Chain PREROUTING (policy ACCEPT 1067 packets, 69118 bytes)
    pkts bytes target prot opt in out source destination

    Chain POSTROUTING (policy ACCEPT 79 packets, 4638 bytes)
    pkts bytes target prot opt in out source destination
    1034 57037 SNATVS all — any any anywhere anywhere
    786 42849 MASQUERADE all — any ETH02 anywhere anywhere
    181 10483 MASQUERADE all — any ppp0 anywhere anywhere

    Chain OUTPUT (policy ACCEPT 204 packets, 14830 bytes)
    pkts bytes target prot opt in out source destination

    Chain SNATVS (1 references)
    pkts bytes target prot opt in out source destination
    root@zeroshell root>

    in reply to: ISP connection setup problem #51168

    xtacy
    Member

    @ifconfig wrote:

    root@zeroshell root> ifconfig
    ETH00 Link encap:Ethernet HWaddr 00:E0:F4:15:A4:64
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:76031782 errors:0 dropped:0 overruns:0 frame:0
    TX packets:49630556 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:1183392016 (1128.5 Mb) TX bytes:3869829057 (3690.5 Mb)
    Interrupt:24 Base address:0xc000

    ETH00:00 Link encap:Ethernet HWaddr 00:E0:F4:15:A4:64
    inet addr:10.54.29.1 Bcast:10.54.29.255 Mask:255.255.255.0
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    Interrupt:24 Base address:0xc000

    ETH01 Link encap:Ethernet HWaddr 00:E0:F4:15:A4:65
    inet addr:10.33.169.85 Bcast:10.33.169.127 Mask:255.255.255.128
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:31623457 errors:0 dropped:0 overruns:0 frame:0
    TX packets:57821538 errors:0 dropped:0 overruns:0 carrier:0
    collisions:9598748 txqueuelen:1000
    RX bytes:2311971396 (2204.8 Mb) TX bytes:1126790893 (1074.5 Mb)
    Interrupt:25 Base address:0xc400

    ETH02 Link encap:Ethernet HWaddr 00:E0:F4:15:A4:66
    inet addr:188.230.21.97 Bcast:188.230.21.255 Mask:255.255.254.0
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:39506871 errors:0 dropped:0 overruns:0 frame:0
    TX packets:37422143 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:3215544688 (3066.5 Mb) TX bytes:1098084078 (1047.2 Mb)
    Interrupt:26 Base address:0xc800

    dummy1 Link encap:Ethernet HWaddr 32:E2:83:E9:1C:EB
    inet addr:192.168.142.142 Bcast:192.168.142.255 Mask:255.255.255.255
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:426471 errors:0 dropped:0 overruns:0 frame:0
    TX packets:426471 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:41543464 (39.6 Mb) TX bytes:41543464 (39.6 Mb)

    ppp0 Link encap:Point-to-Point Protocol
    inet addr:10.96.1.184 P-t-P:10.0.0.1 Mask:255.255.255.255
    UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1
    RX packets:18122247 errors:0 dropped:0 overruns:0 frame:0
    TX packets:20429744 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:3
    RX bytes:4047006462 (3859.5 Mb) TX bytes:1951829921 (1861.4 Mb)

    @iptables -L -v wrote:

    root@zeroshell root> iptables -L -v
    Chain INPUT (policy ACCEPT 3050K packets, 288M bytes)
    pkts bytes target prot opt in out source destination
    3515K 336M SYS_INPUT all — any any anywhere anywhere
    429 24957 SYS_HTTPS tcp — any any anywhere anywhere tcp dpt:http
    4094 568K SYS_HTTPS tcp — any any anywhere anywhere tcp dpt:https
    1527 75492 SYS_SSH tcp — any any anywhere anywhere tcp dpt:ssh

    Chain FORWARD (policy ACCEPT 126M packets, 102G bytes)
    pkts bytes target prot opt in out source destination

    Chain OUTPUT (policy ACCEPT 970K packets, 70M bytes)
    pkts bytes target prot opt in out source destination
    1432K 114M SYS_OUTPUT all — any any anywhere anywhere

    Chain NetBalancer (0 references)
    pkts bytes target prot opt in out source destination

    Chain SYS_HTTPS (2 references)
    pkts bytes target prot opt in out source destination
    0 0 ACCEPT all — lo any anywhere anywhere
    4523 593K ACCEPT all — any any anywhere anywhere

    Chain SYS_INPUT (1 references)
    pkts bytes target prot opt in out source destination
    426K 42M ACCEPT all — lo any anywhere anywhere
    19356 4654K ACCEPT udp — any any anywhere anywhere udp spt:domain state ESTABLISHED
    285 196K ACCEPT tcp — any any anywhere anywhere tcp spt:http state ESTABLISHED
    0 0 ACCEPT tcp — any any anywhere anywhere tcp spt:8245 state ESTABLISHED
    13411 1019K ACCEPT udp — any any anywhere anywhere udp spt:ntp state ESTABLISHED
    3056K 288M RETURN all — any any anywhere anywhere

    Chain SYS_OUTPUT (1 references)
    pkts bytes target prot opt in out source destination
    427K 42M ACCEPT all — any lo anywhere anywhere
    21088 1535K ACCEPT udp — any any anywhere anywhere udp dpt:domain
    402 24090 ACCEPT tcp — any any anywhere anywhere tcp dpt:http
    0 0 ACCEPT tcp — any any anywhere anywhere tcp dpt:8245
    13507 1027K ACCEPT udp — any any anywhere anywhere udp dpt:ntp
    970K 70M RETURN all — any any anywhere anywhere

    Chain SYS_SSH (1 references)
    pkts bytes target prot opt in out source destination
    0 0 ACCEPT all — lo any anywhere anywhere
    1486 73344 ACCEPT all — ETH00 any 10.54.29.3 anywhere
    0 0 DROP all — any any anywhere anywhere

    @iptables -t nat -L -v wrote:

    root@zeroshell root> iptables -t nat -L -v
    Chain PREROUTING (policy ACCEPT 2708K packets, 177M bytes)
    pkts bytes target prot opt in out source destination

    Chain POSTROUTING (policy ACCEPT 9197 packets, 568K bytes)
    pkts bytes target prot opt in out source destination
    2037K 108M SNATVS all — any any anywhere anywhere
    1083K 58M MASQUERADE all — any ETH02 anywhere anywhere
    944K 49M MASQUERADE all — any ppp0 anywhere anywhere

    Chain OUTPUT (policy ACCEPT 177K packets, 14M bytes)
    pkts bytes target prot opt in out source destination

    Chain SNATVS (1 references)
    pkts bytes target prot opt in out source destination

    P.S. both ISPs was turned on

    in reply to: ISP connection setup problem #51167

    xtacy
    Member

    @ppalias wrote:

    Yes i do. I do get responses from google, yahoo, this site or any other alive website at all even if 1st ISP is disconnected physically.

    You mean here that you get responses from any site from the utilities ping, if the first connection is deactivated?

    Yes.
    i mean if 1st IPS’s ethernet cable isn’t connected to ZS’s PC (not just deactivated via Network Setup).
    @ppalias wrote:

    The syntax was ambiguous that is why I am asking.

    I’m sorry about that.

    NB Page

    NetworkSetup Page

    Router Page

    in reply to: ISP connection setup problem #51165

    xtacy
    Member

    @ppalias wrote:

    If you ping from your ZS (utilities menu) do you get a response?

    Yes i do. I do get responses from google, yahoo, this site or any other alive website at all even if 1st ISP is disconnected physically. But every arp finishes with msg like:

    WARNING: the host 62.149.128.154 is not directly connected on the ETH02 LAN but is reachable via
    the gateway 188.230.20.1: ARP is a Layer 2 Protocol and it cannot be routed by routers!

    @ppalias wrote:

    Is your second ISP blocking ICMPs?

    Don’t know
    @ppalias wrote:

    Is your second ISP filtering packets depending on MAC address so that your desktop connects but your ZS fails?

    No. Any connected PC works fine. I guess if I connect their cable to a simple 8ports switch all of 7 PCs connected to that swith would work fine due to ISP’s DCHP. But anyway – is it possible to change the MAC in ZS (like in WinXP)?
    Ping to google.com:

    ARPING 74.125.39.106 from 188.230.21.97 ETH02
    Sent 3 probes (3 broadcast(s))
    Received 0 response(s)

    WARNING: the host 74.125.39.106 is not directly connected on the ETH02 LAN but is reachable via
    the gateway 188.230.20.1: ARP is a Layer 2 Protocol and it cannot be routed by routers!

    PING 74.125.39.106 (74.125.39.106) 56(84) bytes of data.
    64 bytes from 74.125.39.106: icmp_seq=1 ttl=51 time=89.4 ms
    64 bytes from 74.125.39.106: icmp_seq=2 ttl=51 time=60.2 ms
    64 bytes from 74.125.39.106: icmp_seq=3 ttl=51 time=56.6 ms

    — 74.125.39.106 ping statistics —
    3 packets transmitted, 3 received, 0% packet loss, time 2010ms
    rtt min/avg/max/mdev = 56.671/68.765/89.417/14.677 ms

    for zeroshell.net:

    ARPING 95.110.132.149 from 188.230.21.97 ETH02
    Sent 3 probes (3 broadcast(s))
    Received 0 response(s)

    WARNING: the host 95.110.132.149 is not directly connected on the ETH02 LAN but is reachable via
    the gateway 188.230.20.1: ARP is a Layer 2 Protocol and it cannot be routed by routers!

    PING 95.110.132.149 (95.110.132.149) 56(84) bytes of data.
    64 bytes from 95.110.132.149: icmp_seq=1 ttl=49 time=89.6 ms
    64 bytes from 95.110.132.149: icmp_seq=2 ttl=49 time=88.8 ms
    64 bytes from 95.110.132.149: icmp_seq=3 ttl=49 time=86.4 ms

    — 95.110.132.149 ping statistics —
    3 packets transmitted, 3 received, 0% packet loss, time 2007ms
    rtt min/avg/max/mdev = 86.437/88.313/89.682/1.393 ms

    in reply to: Problems with CF preparing for ZS #51029

    xtacy
    Member

    @ppalias wrote:

    CF is treated like a normal hard disk in terms of partitioning and formating.

    It’s not true if CF used via card-reader. Many partition programs just cant c the CF as a drive in that case. When using CF via CF2IDE adapter it is true. But i had problems anyway.
    Also I tried to unmount CF before running fdisk/cfdisk but they doesn’t see the CF at all in that case.
    Well, maybe it because I’m a lamer in *nix OSes… Maybe its due to SLAX is not the best choice of live Linux for such things. But I bet its all about my CF which got some low-level/system bug due to WinXP admin disk tool’s actions. I got such negative experience with new Transcend 4Gb SD-card (not SDHC!) which loses its initial capacity (thanx again to WinXP admin disk tool’s). Now it’s size is about 3Gb and there is nothing i can do but i tried a few tools like SDFormatter, SDFixCapacity etc. and also i tried to format it using HTPC, smartphone, camera etc.

    in reply to: HOWTO: Install ZeroShell on HDD #45581

    xtacy
    Member

    there are also dd tool for Windows and Flashnul tools you can use to write image to HDD or CF. Both are free.
    Flashnul could b used only with flash drives and also (and mainly) is a very good usb-flash specific test tool. The author’s page is in russian but to use it as dd you should type something like:

    flashnul H: -L zeroshell.img

    where
    H: – corresponding usb flash drive (CF)
    -L means Load image to ^ (u could also Save image from usb with -S)
    zeroshell.img – decompressed image

    With that flashnul tool i got success with 1gb image. It made 3 partitions but i made a fatal error. Since first partition become 13 megs instead of initial capacity of my CF(4Gb) i was scared about loosing capacity of CF and deleted all the partitions using WinXP admin tools. After that i couldnt recreate CF partitions for a long time using this and other tools and methods…

    2 saadakhtar
    You dont have to download a 700megs linux live distro. It useless cause you could use the ZS which is much smaller and available right here right now :). Save img to usb-pen-flash-drive then burn ZS iso to CD. boot up ZS with usb-pen-flash-drive connected and choose S 2go2 the shell. Then you just need to mount usb-pen-flash-drive to access it’s folder with image and give shell command like

    gunzip ZS.gz>/dev/hdd

    and thats all you really need 2do.
    If a HDD has some partitions you can also manage it with ZS’s shell using fdisk or cfdisk (im not sure but i guess 1 reboot needed after fdisk/cfdisk managing).

    in reply to: Problems with CF preparing for ZS #51027

    xtacy
    Member

    At last!
    The key is CF need to b not partitioned at all just like HDD. But that is the thing which i couldnt do for a long time. Every time i boot linux CF mounts as hdc1(ZS) or sdb1(slax). But with no partitions it would b just hdc or sdb without any digit.
    I had a problem with unpartitioning my CF. But somehow under ZS booted from CD and with help of fdisk/cfdisk (4 weird ghost partitions was deleted) i get ability to deletethe main partition but in WinXP! Or i just dont know how2 do it in linux cause fdisk/cfdisk was unable to do it. And i did it in WinXP with admin tools. After that i boot ZS from CD again and my CF was seen by fdisk -l like /dev/hdc (not hdc1 like it was b4) and i did gunzip -c ZeroShell-1.0.beta13-CompactFlash-IDE-USB-SATA-1GB.img.gz>/dev/hdc from usb-stick and tada! it works now!

    And the same with HDD – before boot any live linux and doing anything like dd or gupzip>/dev/hdd you must kill all the partitions on this HDD. But with HDDs its much easier 2do. Even with admin tools in WinXP or with any partitioning soft.

    Yes, linux is free but it takes a lot of your time…

    PS when i got stuck i tried physdiskwrite under WinXP and it didnt help. I choose correct usb drive for it but got no changes on CF. It was just damn waste of my time. And any other win programs that acts like linux’s dd (flashnul, dd tool) also didnt help. And linux methods like dd 2 dev or gunzip 2 dev also. now i know why.

    thanx for replies!!!

    in reply to: Installing ZeroShell in Hard Disk #45143

    xtacy
    Member

    At last!
    The key is CF need to b not partitioned at all just like HDD. But that is the thing which i couldnt do for a long time. Every time i boot linux CF mounts as hdc1(ZS) or sdb1(slax). But with no partitions it would b just hdc or sdb without any digit.
    I had a problem with unpartitioning my CF. But somehow under ZS booted from CD and with help of fdisk/cfdisk (4 weird ghost partitions was deleted) i get ability to deletethe main partition but in WinXP! Or i just dont know how2 do it in linux cause fdisk/cfdisk was unable to do it. And i did it in WinXP with admin tools. After that i boot ZS from CD again and my CF was seen by fdisk -l like /dev/hdc (not hdc1 like it was b4) and i did gunzip -c ZeroShell-1.0.beta13-CompactFlash-IDE-USB-SATA-1GB.img.gz>/dev/hdc from usb-stick and tada! it works now!

    And the same with HDD – before boot any live linux and doing anything like dd or gupzip>/dev/hdd you must kill all the partitions on this HDD. But with HDDs its much easier 2do. Even with admin tools in WinXP or with any partitioning soft.

    Yes, linux is free but it takes a lot of your time…

    in reply to: Installing ZeroShell in Hard Disk #45142

    xtacy
    Member

    well fat32 fs really doesnt supportd by kernel and i got corresponding msg at boot. damn!
    What should i do now?
    CF refuses any fs except fat32. I did partitions using fdisk and cfdisk with writing changes but fat32 and all the CF’s files was accessible after that. So i cant format it in any other fs… no ext2 – no ZS. its a deadlock and it drive me nuts!

    in reply to: Installing ZeroShell in Hard Disk #45141

    xtacy
    Member

    @ppalias wrote:

    The default line is

    /dev/cdrom              /cdrom              iso9660 ro 0 0

    but you were change it in your tutor to:

    /dev/cdrom /cdrom ext2 ro 0 0

    . So i was guessing you mean than this “cdrom” is really hda5 due to ext2 fs and cause there is no hda5 devices described at all. So you can write just rw instead of ro.
    Anyway i got the bootup menu with my fat32 formatted CF using the handy tool Universal USB Installer. but when it tries 2 boot it searches for CDROMs (i c the Probing CDROM msgs) but there is no any connected. So it gives up and hangs with kernel panic bla-bla-bla something about VFS and block(1,2)…
    Im working now on initrd.gz and rootfs changes (iso’s original used for now). Dunno if it helps me out…
    PS It is the 3rd day im trying to install ZS to CF with no result… im not sure about my patience….

    in reply to: Installing ZeroShell in Hard Disk #45139

    xtacy
    Member

    thanx for reply, i’ll try it.
    well, what gonna happens if you’ll do:

    /dev/cdrom /cdrom ext2 defaults 0 0

    i mean no ro attr for cdrom device?
    im Interesting what i should write here if i have fat32 insead of ext2 – vfat or fat32?

    and about the physdiskwrite – i did try it but it doesnt write to my CF. It was just dumb time loose with no changes in CF.

    in reply to: Installing ZeroShell in Hard Disk #45137

    xtacy
    Member

    while trying to setup my CF with this method…
    CF is vfat/fat32 and it couldnt b properly formatted as ext2… dunno why.

    1st problem got at
    cp -rp * ..
    it refuses to copy a bunch of filles and dirs due 2 permissions…

    2nd
    @fergon wrote:

    Now the system is ready, only rest to make it bootable. With grub, append in /boot/grub/menu.lst
    title ZeroShell
    root (hd0,4)
    kernel /isolinux/vmlinuz quiet root=/dev/ram2 ramdisk_size=131072 init=/bin/init
    initrd /isolinux/initrd.gz
    boot

    i guess one just need to type grub and type it line by line?
    but at line initrd /isolinux/initrd.gz it said “file too big to fit in memory”…

    anyway i’m curios if it could work with fat32 fs?

    in reply to: Problems with CF preparing for ZS #51024

    xtacy
    Member

    @ppalias wrote:

    You can read the tutorial -> http://digilander.libero.it/smasherdevourer/schede/linux/Zeroshell%20su%20HD-EN.pdf
    It is the same for HD and CF.

    You probably didn’t read my post. The manual’s method is the same i already did several times. There is no difference between my method:

    gunzip -c ZeroShell-1.0.beta13-CompactFlash-IDE-USB-SATA-1GB.img.gz | dd of=/dev/sdb1

    and manual’s method:

    gunzip -c zeroshell.img>/dev/sdb1

    But anyway i tried it and it made same 3 partitions with same result. Making 1st partition active doesn’t change anything.

    But now i got the new result – GRUB loading error 17 which means something like “can’t mount selected partition”.

    I guess i need some tool to extract this img-file and do all the things manually including CF partitioning, making it bootable etc. Looks like there is something wrong with dd or my CF… Tried to make the CF on 2 different PCs with different card readers and with the same result…

    in reply to: how2 setup&run ZS on PC with 256Mb RAM & built-in CF #51016

    xtacy
    Member

    My PC exceeds the MSR (Minimum System Requirements).
    But there is no newer than beta 9 version in Description column… Should i use the
    1GB image for IDE, SATA e USB disks 1.0.beta13 July 2, 2010 ZeroShell-1.0.beta13-CompactFlash-IDE-USB-SATA-1GB.img.gz 132MB?
    well, i’ll try it anyway.
    thanx.

Viewing 15 posts - 1 through 15 (of 16 total)