The problem with NetBalancer

Home Page Forums Network Management ZeroShell The problem with NetBalancer

This topic contains 16 replies, has 0 voices, and was last updated by  777maxism 8 years, 9 months ago.

Viewing 15 posts - 1 through 15 (of 18 total)
  • Author
    Posts
  • #42476

    777maxism
    Member

    There was now a problem in the failover monitor appeared here this line (Status: Not Running), when it’s all included. Why is that?

    #50609

    777maxism
    Member
    #50610

    ppalias
    Member

    There is something wrong with the upload.com.ua site and is not letting me open the image.

    Ваш IP: 79.166.239.203 non UA-IX

    I suppose that is not letting me download as I am not in Ukraine.

    #50611

    777maxism
    Member

    Sorry this Ukrainian exchanger.
    I restarted here
    http://rapidshare.com/files/405017946/ZS12_failover.JPG

    #50612

    ppalias
    Member

    Check on the log for any error and post it here. Switch the mode from “Failover” to “Load Balancing and Failover” and check if it works.

    #50613

    777maxism
    Member

    In the logs wrote:

    11:18:04 Default Route has been changed: nexthop via 212.3.96.x weight 10 realm 100 nexthop dev ppp0 weight 98 realm 103 nexthop via 193.200.33.x weight 99 realm 104 nexthop via 85.198.133.x weight 1 realm 105 nexthop via 192.168.192.1 weight 95 realm 106 nexthop via 85.198.133.x weight 2 realm 107 nexthop dev ppp1 weight 90 realm 108
    11:18:04 Failover monitor has started
    11:18:08 Default Route has been changed: nexthop via 193.200.33.x weight 99 realm 104
    11:18:08 Failover monitor has started

    11:18:05 SUCCESS: Net Balancer configuration successfully saved
    11:18:09 SUCCESS: Net Balancer configuration successfully saved

    But it says Status: Not Running

    And what is the error in the logs? They do not relate to the Failover Monitor.

    11:18:00 message repeated 65 times
    11:18:01 APIC error on CPU0: 02(02)
    11:18:04 message repeated 9 times
    11:18:04 APIC error on CPU0: 02(02)
    11:18:06 APIC error on CPU0: 02(02)
    11:18:08 message repeated 6 times
    11:18:08 APIC error on CPU0: 02(02)
    11:18:08 APIC error on CPU0: 02(02)
    11:18:09 APIC error on CPU0: 02(02)
    11:18:40 message repeated 87 times
    11:19:00 message repeated 60 times

    #50614

    ppalias
    Member

    Open a shell and run the following command:

    ps -ef | grep failover

    if you get an output it means that failover is running and there is a bug showing Failover down.

    #50615

    777maxism
    Member

    http://rapidshare.com/files/405081749/ZS12_failover_new.JPG
    something that has issued
    I think reinstall the version on the ZS 13 may issue goes …

    #50616

    ppalias
    Member

    Try to disable temporarily some interfaces from the netbalancer list. Leave 2 of them and see if the error continues.

    #50617

    777maxism
    Member

    Interesting situation … I knew about where the problem but did not understand why? In the picture if you look there (Gateway – Optima3 Interface ppp1) So if you turn it off then it works … And when you turn off just this (Gateway) in the other versions, if left enabled (Geteway Optima3) in status is not running.

    #50618

    ppalias
    Member

    You mean that if you disable ppp1 from the Netbalancer you have everything else working fine?

    #50619

    777maxism
    Member

    @ppalias wrote:

    You mean that if you disable ppp1 from the Netbalancer you have everything else working fine?

    Yes, exactly.
    And I re-created in the Net Balancer this gateway to the new, the result is the same …
    This it self is the connection is fully working.
    Probably what is a bug in version …

    #50620

    ppalias
    Member

    I wonder if it is a bug of the number of total connections. Can you temporerily erase another connection so that with Optima3 you got 6 connections in total? Or only Optima3 has a problem regardless the number of total connections? Can you post a screenshot of Optima3 connection in Netbalancer?

    #50621

    777maxism
    Member

    @ppalias wrote:

    I wonder if it is a bug of the number of total connections. Can you temporerily erase another connection so that with Optima3 you got 6 connections in total? Or only Optima3 has a problem regardless the number of total connections? Can you post a screenshot of Optima3 connection in Netbalancer?

    Well I’ll try, lay out the screenshots.

    #50622

    777maxism
    Member

    @ppalias wrote:

    I wonder if it is a bug of the number of total connections. Can you temporerily erase another connection so that with Optima3 you got 6 connections in total? Or only Optima3 has a problem regardless the number of total connections? Can you post a screenshot of Optima3 connection in Netbalancer?

    Hi, this is again, I am the problem. I found myself ZS V13 problem remained and he had found the cause, it is connected with the number of 6 records. In the installation 5 locks work properly, as soon as you enter your 6 gateway status (Failover Monitor) value appears (Status: Not Running).
    Screened for V12, V13.
    Perhaps even that is a bug v12 because, I configuration backup with version v12 and v13 versions installed on.

Viewing 15 posts - 1 through 15 (of 18 total)

You must be logged in to reply to this topic.