This topic contains 12 replies, has 0 voices, and was last updated by 
Viewing 14 posts - 1 through 14 (of 14 total)
-
Posts
-
Hi all,
I am getting this error – 113 No route to host, when trying to update a debian computer with apt-get.
I think its something from the settings, I did disable the http proxy but still getting the same error.
Thanks in advance 😀Hi!
Please show output of these commands:
# ifconfig -a
# route -nifconfig -a
DEFAULTBR Link encap:Ethernet HWaddr AE:74:96:9A:9E:D7
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
ETH00 Link encap:Ethernet HWaddr 00:24:01:2F:67:AA
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:69984 errors:0 dropped:0 overruns:0 frame:0
TX packets:72909 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8200930 (7.8 Mb) TX bytes:64090223 (61.1 Mb)
Interrupt:9 Base address:0x8c00
ETH00:00 Link encap:Ethernet HWaddr 00:24:01:2F:67:AA
inet addr:10.10.10.1 Bcast:10.10.10.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:9 Base address:0x8c00
ETH01 Link encap:Ethernet HWaddr 00:24:01:2F:67:A9
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1367241 errors:0 dropped:0 overruns:0 frame:0
TX packets:1830576 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:239668903 (228.5 Mb) TX bytes:1701907017 (1623.0 Mb)
Interrupt:10 Base address:0xa800
ETH01:00 Link encap:Ethernet HWaddr 00:24:01:2F:67:A9
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:10 Base address:0xa800
ETH02 Link encap:Ethernet HWaddr 00:B0:D0:B8:4D:88
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:49612947 errors:0 dropped:0 overruns:1 frame:0
TX packets:1320036 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3853478207 (3674.9 Mb) TX bytes:178774609 (170.4 Mb)
Interrupt:5 Base address:0xe400
ETH02:01 Link encap:Ethernet HWaddr 00:B0:D0:B8:4D:88
inet addr:93.152.164.179 Bcast:93.152.167.255 Mask:255.255.252.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:5 Base address:0xe400
VPN99 Link encap:Ethernet HWaddr 00:FF:EC:D1:0B:79
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
VPN99:00 Link encap:Ethernet HWaddr 00:FF:EC:D1:0B:79
inet addr:192.168.250.254 Bcast:192.168.250.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
dummy0 Link encap:Ethernet HWaddr 8E:76:8D:2F:F2:A6
inet addr:192.168.141.142 Bcast:192.168.141.255 Mask:255.255.255.0
BROADCAST NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
dummy1 Link encap:Ethernet HWaddr 5E:C2:C5:B1:DA:2E
inet addr:192.168.142.142 Bcast:192.168.142.255 Mask:255.255.255.255
UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:62533 errors:0 dropped:0 overruns:0 frame:0
TX packets:62533 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5026435 (4.7 Mb) TX bytes:5026435 (4.7 Mb)
route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 ETH01
192.168.250.0 0.0.0.0 255.255.255.0 U 0 0 0 VPN99
10.10.10.0 0.0.0.0 255.255.255.0 U 0 0 0 ETH00
93.152.164.0 0.0.0.0 255.255.252.0 U 0 0 0 ETH02
0.0.0.0 93.152.164.1 0.0.0.0 UG 0 0 0 ETH02
sorry for the delay 😕
Sorry, my post was not clear enough. 😕 I want you to run those commands on Debian box.
“No route to host” means that you have incorrectly configured network interface settings (IP-address, netmask) or incorrectly set the default router parameters on the client side, imho.
Ill post them tonight, first to get the vpn working 😀
ifconfig -a
bond0 Link encap:Ethernet HWaddr 00:1b:11:c4:71:3e
inet6 addr: fe80::21b:11ff:fec4:713e/64 Scope:Link
UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:1014790 errors:0 dropped:0 overruns:0 frame:0
TX packets:603975 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1321577133 (1.2 GiB) TX bytes:49602532 (47.3 MiB)
eth0 Link encap:Ethernet HWaddr 00:1b:11:c4:71:3e
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:454375 errors:0 dropped:0 overruns:0 frame:0
TX packets:295269 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:595180539 (567.6 MiB) TX bytes:25401737 (24.2 MiB)
Interrupt:19
eth1 Link encap:Ethernet HWaddr 00:1b:11:c4:71:3e
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:560415 errors:0 dropped:0 overruns:0 frame:0
TX packets:308706 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:726396594 (692.7 MiB) TX bytes:24200795 (23.0 MiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:18796 errors:0 dropped:0 overruns:0 frame:0
TX packets:18796 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5944713 (5.6 MiB) TX bytes:5944713 (5.6 MiB)
venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:29163 errors:0 dropped:0 overruns:0 frame:0
TX packets:7155 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2066836 (1.9 MiB) TX bytes:1428863 (1.3 MiB)
vmbr0 Link encap:Ethernet HWaddr 00:1b:11:c4:71:3e
inet addr:10.10.10.2 Bcast:10.10.10.255 Mask:255.255.255.0
inet6 addr: fe80::21b:11ff:fec4:713e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:996356 errors:0 dropped:0 overruns:0 frame:0
TX packets:590496 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1303252499 (1.2 GiB) TX bytes:45017894 (42.9 MiB)
vmtab106i0 Link encap:Ethernet HWaddr 00:ff:7c:b3:a8:8c
inet6 addr: fe80::2ff:7cff:feb3:a88c/64 Scope:Link
UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
RX packets:8939 errors:0 dropped:0 overruns:0 frame:0
TX packets:20869 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:500
RX bytes:1645177 (1.5 MiB) TX bytes:2528965 (2.4 MiB)
route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.10.10.3 0.0.0.0 255.255.255.255 UH 0 0 0 venet0
192.168.0.123 0.0.0.0 255.255.255.255 UH 0 0 0 venet0
77.70.60.194 0.0.0.0 255.255.255.255 UH 0 0 0 venet0
77.70.60.210 0.0.0.0 255.255.255.255 UH 0 0 0 venet0
10.10.10.0 0.0.0.0 255.255.255.0 U 0 0 0 vmbr0
0.0.0.0 10.10.10.1 0.0.0.0 UG 0 0 0 vmbr0
I double checked and everything is ok.
Can you ping 10.10.10.1 ?
I can, tried everything and it seems to be working. I can even ping the IP’s of the debain update servers, but cant download. I once had a problem with ubuntu in my home network and it turned out to be the proxy I was using, but there is no proxy. Can it be from the ISP?
Looks like debian specific issue. Can you show output of
wget http://http.us.debian.org/debian/wget http://http.us.debian.org/debian/
--2009-06-29 10:49:33-- http://http.us.debian.org/debian/
Resolving http.us.debian.org... 204.152.191.39, 35.9.37.225, 64.50.238.52, ...
Connecting to http.us.debian.org|204.152.191.39|:80... failed: No route to host.
Connecting to http.us.debian.org|35.9.37.225|:80... failed: No route to host.
Connecting to http.us.debian.org|64.50.238.52|:80... failed: No route to host.
Connecting to http.us.debian.org|128.30.2.36|:80... failed: No route to host.
Connecting to http.us.debian.org|149.20.20.135|:80... failed: No route to host.
Ill call the ISP, I am beging to doubt that the problem is in th zeroshell box.
PS I can update using equo on my Sabayon laptop. Somewhere in here I had a ubuntu cd, ill try it in 15 mins or so.
So, you can ping external sites but cannot browse them because of routing problem. Very strange :shock:. I’m afraid I can’t help you.
Not enough information here to troubleshoot your connectivity issue.
I actuallt fixed it last night. Don’t know how but when I made a new profile in zeroshell, all worked perfectly. 😀
Viewing 14 posts - 1 through 14 (of 14 total)
You must be logged in to reply to this topic.