Lan intefaces not available on ibase FWA8206

Home Page Forums Network Management Networking Lan intefaces not available on ibase FWA8206

This topic contains 8 replies, has 0 voices, and was last updated by  Sker 8 years, 9 months ago.

Viewing 10 posts - 1 through 10 (of 10 total)
  • Author
    Posts
  • #42695

    Sker
    Member

    I am new to the zeroshell router firewall world . I have installed the 1.0.beta13 image on a 4Gb CF card on an ibase FWA8206 . and from the console the appliance seems to have booted successfully .

    Unfortunately I can’t get the web interface to work . When I checked console and check the network setup none of the Ethernet interfaces seem to be available. If I try to assign an I address to Eth00 I get an error saying the interface is invalid.

    The FWA8206 comes with Six Intel 82547L PCI Express Gigabit LAN interfaces. Are the drivers for this interface included in the image ?

    I am not a Linux expert so any advice on how / what to check or do next would be appreciated ?

    #51223

    ppalias
    Member

    On the console can you run these commands and paste the output here?

    lspci
    lsmod
    ifconfig -a
    #51224

    Sker
    Member

    Below is the o/p of the commands

    Thanks
    Sker

    lspci
    00:00.0 Host bridge: Intel Corporation 82Q35 Express DRAM Controller (rev 02)
    00:02.0 VGA compatible controller: Intel Corporation 82Q35 Express Integrated Graphics Controller (rev 02)
    00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02)
    00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02)
    00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02)
    00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02)
    00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02)
    00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 02)
    00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 02)
    00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 02)
    00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02)
    00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 02)
    00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02)
    00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02)
    00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02)
    00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02)
    00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92)
    00:1f.0 ISA bridge: Intel Corporation 82801IB (ICH9) LPC Interface Controller (rev 02)
    00:1f.2 IDE interface: Intel Corporation 82801IB (ICH9) 2 port SATA IDE Controller (rev 02)
    00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02)
    00:1f.5 IDE interface: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE Controller (rev 02)
    01:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
    02:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
    03:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
    04:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
    05:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
    06:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
    07:01.0 Mass storage controller: Integrated Technology Express, Inc. ITE 8211F Single Channel UDMA 133 (rev 11)

    root@zeroshell root> lsmod
    Module Size Used by
    dummy1 5376 0
    xt_CONNMARK 5760 1
    tun 13696 0
    bridge 57752 0
    llc 9228 1 bridge
    iptable_nat 9224 1
    xt_state 4352 4
    xt_tcpudp 4992 11
    iptable_mangle 5248 1
    iptable_filter 5376 1
    ip_tables 16144 3 iptable_nat,iptable_mangle,iptable_filter
    x_tables 19076 5 xt_CONNMARK,iptable_nat,xt_state,xt_tcpudp,ip_tables
    nf_nat_pptp 5632 0
    nf_nat_proto_gre 4740 1 nf_nat_pptp
    nf_nat_ftp 5248 0
    nf_nat 21656 4 iptable_nat,nf_nat_pptp,nf_nat_proto_gre,nf_nat_ftp
    nf_conntrack_ipv4 19720 8 iptable_nat,nf_nat
    nf_conntrack_tftp 7060 0
    nf_conntrack_pptp 8964 1 nf_nat_pptp
    nf_conntrack_proto_gre 8064 1 nf_conntrack_pptp
    nf_conntrack_irc 8604 0
    nf_conntrack_sip 11156 0
    nf_conntrack_ftp 11300 1 nf_nat_ftp
    nf_conntrack_h323 51912 0
    nf_conntrack 67668 14 xt_CONNMARK,iptable_nat,xt_state,nf_nat_pptp,nf_nat_ftp,nf_nat,nf_conntrack_ipv4,nf_conntrack_tftp,nf_conntrack_pptp,nf_conntrack_proto_gre,nf_conntrack_irc,nf_conntrack_sip,nf_conntrack_ftp,nf_conntrack_h323
    dummy 5376 0
    vfat 14976 0
    fat 54432 1 vfat
    uhci_hcd 26892 0
    ehci_hcd 38540 0
    iTCO_wdt 14116 0
    iTCO_vendor_support 5764 1 iTCO_wdt
    ata_generic 10244 0
    ata_piix 24068 0
    pata_it821x 13572 0
    libata 165192 3 ata_generic,ata_piix,pata_it821x
    dock 12304 1 libata
    loop 20100 1

    root@zeroshell root> ifconfig -a
    DEFAULTBR Link encap:Ethernet HWaddr B6:CB:7A:7A:68:50
    BROADCAST MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    VPN99 Link encap:Ethernet HWaddr 00:FF:E9:77:5E:9E
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    VPN99:00 Link encap:Ethernet HWaddr 00:FF:E9:77:5E:9E
    inet addr:192.168.250.254 Bcast:192.168.250.255 Mask:255.255.255.0
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

    dummy0 Link encap:Ethernet HWaddr 7A:B3:8F:B8:D9:73
    inet addr:192.168.141.142 Bcast:192.168.141.255 Mask:255.255.255.0
    BROADCAST NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    dummy1 Link encap:Ethernet HWaddr 9E:EC:1A:91:7C:88
    inet addr:192.168.142.142 Bcast:192.168.142.255 Mask:255.255.255.255
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:149 errors:0 dropped:0 overruns:0 frame:0
    TX packets:149 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:16059 (15.6 Kb) TX bytes:16059 (15.6 Kb)

    root@zeroshell root>

    #51225

    ppalias
    Member

    There seems to be no module loaded to recognize the NICs. You either will have to compile the module by yourself or report it as a bug so that it will be included in the next version. Although I am sure it will be included in the next version that will have a newer kernel.

    #51226

    Sker
    Member

    I have got a copy of the drivers (e1000e-1.2.10.tar.gz) for the card but when I run the make install in the extracted src folder I get the following errors

    root@zeroshell src> make install
    Makefile:71: *** Kernel header files not in any of the expected locations.
    Makefile:72: *** Install the appropriate kernel development package, e.g.
    Makefile:73: *** kernel-devel, for building kernel modules and try again. Stop.
    root@zeroshell src>

    Can you let me know how I should compile the module

    Thanks

    #51227

    ppalias
    Member

    Hope this post will help you. 🙂

    #51228

    Sker
    Member

    I was afraid you were going to point me to that . I tired this but am not a linux person so I was hoping there was a differnet option.

    I’ll try this again with hopefully some help from google on how to do the steps that are “not described here”:?

    #51229

    ppalias
    Member

    You can always ask for some help if you get stuck.

    #51230

    Sker
    Member

    Found an image that has the drivers and works fine on the hardware platform.

    http://www.zeroshell.net/eng/forum/viewtopic.php?t=1787&highlight=e1000e

    now my problem is that I need this on a CF card but don’t know how to change this ISO to bootable IMG ❓

    #51231

    Sker
    Member

    Tried to make a bootable cf card from this but It fails to boot. Are there any good howto’s on truning the iso into a bootable img

    Thanks

Viewing 10 posts - 1 through 10 (of 10 total)

You must be logged in to reply to this topic.