Home Page › Forums › Network Management › ZeroShell › DSL modem connect ends up in Hardware removed/Remove Config
- This topic is empty.
-
AuthorPosts
-
March 31, 2010 at 4:47 pm #42313
Pit
MemberHello,
i preconfigured a box with 5 networkcards at home:
ETH00 192.168.7.75 is my internal net reachable over a BRIDGE00
ETH01 87.234.250.2 is my Gateway to Internet.
I configured ETH02-04 as PPPoE with Load Balancing.
At the location i connect three DSL-modems to ETH02-04 :
Setup/Network now shows following:
ETH04 has gone. ETH02-03 shows Hardware removed/Remove Config
Has anybody an idea what is going on?
Thanks in advance
Pit
April 1, 2010 at 8:17 am #49975ppalias
MemberIs the hardware firmly attached on the motherboard? Open a shell and write the command “lspci” to check what pci devices are installed. Paste the output here.
April 1, 2010 at 10:51 am #49976Pit
MemberHello ppalias,
thank you for your reply and the hint with lspci.
The output is:root@zeroshell root> lspci
00:00.0 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.1 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.2 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.3 Host bridge: VIA Technologies, Inc. PT890 Host Bridge
00:00.4 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.7 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237/VX700 PCI Bridge
00:08.0 Ethernet controller: Intel Corporation 82541PI Gigabit Ethernet Controller (rev 05)
00:0a.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306 Fire II IEEE 1394 OHCI Link Layer Controller (rev 80)
00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78)
01:00.0 VGA compatible controller: VIA Technologies, Inc. CN700/P4M800 Pro/P4M800 CE/VN800 [S3 UniChrome Pro] (rev 01)
root@zeroshell root>As you can see the ethernetblock for 3 realtek cards is missing.
My other identical machine shows in addition 3 times:00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet (rev 10)
Maybe that this block is broken from one day to the other. People on-site say that the block is connected properly and led’s are working.
I think it is a problem of broken hardware and not of zeroshell.
Thanks again for the hint.
Regards
Pit -
AuthorPosts
- You must be logged in to reply to this topic.