Reply To: Trouble getting to the web control panel

Home Page Forums Network Management ZeroShell Trouble getting to the web control panel Reply To: Trouble getting to the web control panel

#49400

Spinal
Member

@jt wrote:

You probably know about the Setup–>https tab–>Allow access only from (IP or subnet) settings. Of course, if these get set wrong, you can’t get in to fix it.

Have you tried this: (from the FAQ)

Having incorrectly configured the firewall or the network in general I can no longer connect via the web interface. Even rebooting the system doesn’t work. How can I resolve the problem?

From the ZeroShell console press the Z key. This enables the system to start the Fail-Safe procedure: you will be requested to select an Ethernet interface which can be attributed an IP address of your choice; any obstacles, such as firewall rules, belonging to a bridge, static routes or other will be removed. Once complete, you can access the interface via the IP address you attributed. To exit the Fail-Safe mode you must reboot, having removed the obstacle that blocked access.

This is my first whack at ZS, so I’ve never even seen the web-interface!

Sorry for the late reply, had a client who had a virus outbreak and ended up spending a while on site away from home…

Below is the dump from nmap – I don’t see anything on port 443… (oh, and I’ve tried reburning the disk).

The network connection definetly works, I could ssh/scp from the ZS box to my laptop to grab the nmap file…

So my three options:
– Server hardware is the issue (Dell 1u something-or-other) (most unlikely)
– Laptop is the issue (windows Vista… so quite possible it doesn’t like something. I did notice the scp took longer than it should have, so possibly it’s timing out before ZS responds…)
– ZS software (very unlikely as it works for everyone else and it a clean burn, verified, with no changes to the config)

Hmm… I’m confused…
M.


Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name
tcp 0 0 127.0.0.1:389 0.0.0.0:* LISTEN 1629/slapd
tcp 0 0 0.0.0.0:749 0.0.0.0:* LISTEN 4044/kadmind
tcp 0 0 127.0.0.1:389 127.0.0.1:59945 TIME_WAIT -
tcp 0 0 127.0.0.1:59948 127.0.0.1:389 TIME_WAIT -
tcp 0 0 127.0.0.1:389 127.0.0.1:59946 TIME_WAIT -
tcp 0 0 127.0.0.1:59947 127.0.0.1:389 TIME_WAIT -
udp 0 0 0.0.0.0:464 0.0.0.0:* 4044/kadmind
udp 0 0 192.168.142.142:88 0.0.0.0:* 4041/krb5kdc
udp 0 0 192.168.250.254:88 0.0.0.0:* 4041/krb5kdc
udp 0 0 192.168.0.75:88 0.0.0.0:* 4041/krb5kdc
udp 0 0 192.168.142.142:750 0.0.0.0:* 4041/krb5kdc
udp 0 0 192.168.250.254:750 0.0.0.0:* 4041/krb5kdc
udp 0 0 192.168.0.75:750 0.0.0.0:* 4041/krb5kdc
udp 0 0 192.168.250.254:123 0.0.0.0:* 3978/ntpd
udp 0 0 192.168.141.142:123 0.0.0.0:* 3978/ntpd
udp 0 0 192.168.0.75:123 0.0.0.0:* 3978/ntpd
udp 0 0 127.0.0.1:123 0.0.0.0:* 3978/ntpd
udp 0 0 0.0.0.0:123 0.0.0.0:* 3978/ntpd
Active UNIX domain sockets (servers and established)
Proto RefCnt Flags Type State I-Node PID/Program name Path
unix 2 [ ] DGRAM 190 941/udevd @/org/kernel/udev/udevd
unix 7 [ ] DGRAM 2250 1713/syslogd /dev/log
unix 2 [ ] DGRAM 5423 4151/cron
unix 2 [ ] DGRAM 5108 4044/kadmind
unix 2 [ ] DGRAM 5089 4041/krb5kdc
unix 2 [ ] DGRAM 4914 3978/ntpd
unix 2 [ ] DGRAM 2293 1722/klogd

EDIT: Oh, and yes I had tried the failsafe mode…and have tried again…

EDIT2: rebooted into OsX just to see if it was indeed vista… still can’t get anywhere… running OsXs built in portscan (which frankly is quite crappy) I get only 749 open.


Port Scan has started ...

Port Scanning host: 192.168.0.75

Open TCP Port: 749 kerberos-adm
Port Scan has completed ...

Next, I’m going to eliminate the server hardware… going to try with a second laptop running ZS… if I still can’t connect, then it’s either the switch (an old 48-port AT switch) or the cables…

M.